Hello! Welcome to the website of Dongguan pinye Electronics Co., Ltd!

The transformer skeleton is a power device that is responsible for voltage conversion, power transmission, and terminal distribution in the power system. If there is a defect or fault in the high and low voltage side casing of the transformer frame, it will directly endanger the safe operation of the transformer skeleton and its power supply reliability. For the low-pressure side casing, because of its simple structure, it requires short inspection time and convenient maintenance. For the high-pressure side casing (oil-paper capacitor casing), due to its complicated structure and long maintenance period, it is difficult to overhaul. Therefore, it is very important to timely repair and maintain the oil-paper capacitive casing to reduce and eliminate casing accidents.

First, the cause analysis

Through the analysis of the previous casing failure, the following main reasons are summarized:

After the surface of the casing is dirty and absorbs moisture, the insulation resistance is lowered, and the result is that flashover is likely to occur, causing tripping. At the same time, flashover can also damage the surface of the casing. After the dirt absorbs moisture, the conductivity is improved, which not only causes surface flashover, but also may increase the leakage current, causing the insulation sleeve to heat up and cause porcelain damage or even breakdown.

Due to the failure of the casing gasket seal, the top seal of the oil-paper capacitive casing is poor, which may cause the water to break through the insulation, and the poor sealing of the lower part causes the casing to seep, resulting in a drop in the oil level. There are two main reasons for the failure of the casing seal: one is due to insufficient experience of the maintenance personnel, the fastening force is not enough; the second is due to the over-period operation or the quality of the rubber pad.

Others, such as the failure of the grounding small casing, cause the final screen of the casing to generate a floating potential, and partial discharge occurs; the structure of the casing itself is unreasonable and has defects. For example, the main transformer casing of the substation of the transformer skeleton is soldered by the lead wire and the lead wire. The 220 kV A phase casing is the aluminum tube, the wire head is made of copper, and the rain cap is made of aluminum. The copper-aluminum connection causes an increase in contact resistance, so that the rain cap and the conductive head are sintered, and the lead and the conductive head are boiled.

In addition, the casing oil standard pipe is dirty, the oil level is not clear, and a deficit oil is formed after pre-test sampling every year. For human reasons, for example, in the overhaul of the casing, the vacuum is not completely exhausted, so that the air remains between the screens. After the operation, under the action of the high electric field, partial discharge occurs, and even the insulation layer breaks down, causing an accident. Furthermore, the casing head structure is not properly installed. For example, the contact between the lead head and the rain cap is not tight; the rain cap is not tight with the wiring nose; the contact between the wiring nose and the terminal block is poor, and the contact resistance is increased, and the lead joint is heated and sintered.

Second, countermeasures

Through the analysis of the operation of the transformer skeleton casing, it is not difficult to find two ways to form defects: one is that the casing itself has weak links; the other is the human factor, which is caused by the casing installation and maintenance personnel in the operation. After analyzing the main causes of casing failure, we can formulate corresponding countermeasures from the aspects of storage, transportation, installation, overhaul, and overhaul.

First of all, transportation should pay attention to the problem. Lifting speed should be slow to avoid collision with other objects; when lifting and erecting, use the lifting lugs on the flange and tie the upper part of the casing with hemp rope to prevent dumping; be careful not to lift the casing porcelain skirt to prevent wire rope and porcelain The sleeves are damaged by collision; when erecting the casing, any part should be prevented from landing; when the casing is placed and transported, it should be placed in a special box. There should be two support points at the mounting flange. There should be no support for the porcelain skirt at the upper end, and support points for the tail, and the support points should be padded with soft objects. The casing should be fixed in the box to avoid turbulence damage during transportation.